Replace Lock in UPVC Door
A professional locksmith is required for your upvc door locks if they aren't working correctly. They are quick, efficient and finish the job to a high standard.
It's not difficult to change a upvc bar lock. It's just a matter of knowing what you need to do and follow the steps below.
Removing the Barrel Lock
uPVC windows and doors are common in many types of homes. They are great for allowing natural light into the home and are easy to open using the right key. It takes only five minutes to replace the barrel of a lock on uPVC uPVC. It's a quick fix if you've lost your key, or if a tenant has moved out and not returned it or the barrel of the lock is damaged.
You'll need to take out the handle screws first. This is to remove the handles out of the way to access the lock barrel screw. Be careful not to loosen the screws too quickly because this could cause damage to the handles or cause them to fall off while you are working.
Once the screws have been removed After removing the screws, look for the screw on the inside of the door that holds the lock on the barrel. This screw stands out and is a different color than the other screws on the door. Take it off using a Phillips screwdriver. Then, take the current key used to open the lock and place it in the barrel. Turn it as far to the right as you can. This should release the barrel and make it easier to pull it out of the door.
After you've loosen the screw it's time to break the pins holding the euro cylinder in place. You will need pliers with strength, or mole grips to accomplish this. Take the protruding portion of the euro cylinder, and bend it from side to side, and then up and down. This will break the support pins that hold it in place.
Once the old cylinder is gone, you can start the process of putting in the new one. First, you will need to measure the size of the lock cylinder in order to make sure you have purchased the appropriate replacement. This can be accomplished by measuring the distance from the center of the circular part of the keyhole to the middle of the square spindle. The measurement should be taken at the top of the spindle.
Change the Cylinder
The primary locking mechanism is a euro cylinder. It is easy to change and don't need a locksmith or handyman service. In fact, if yours isn't anti-snap, anti-bump or anti-sn should be changed to one with this protection included. They aren't expensive and could save money and inconvenience in the case that your locks are compromised.
Open the door and stand in the front of it. This will allow you to easily reach the handle retaining screws by hand or with an appropriate tool. You can loosen the screw a bit maybe a quarter-turn to begin.
The cylinder will now be easily removed since the screw will stop holding it in place. Next, you will need to decide what size replacement cylinder you require. There are about 25 sizes available. You should bring your previous cylinder with you when you purchase a new one to ensure it fits.
If you're not sure what the size is then measure from the center of the screw hole to the end of the cylinder. This is the only way to make sure you are getting the correct size cylinder for your Upvc doors.
Once you have the replacement cylinder in place, you can insert it into your door reverse to the way you removed the old one. It could be tricky to align the lock cam, but it is usually an issue with alignment and will be fixed eventually.
You will now need to screw the long screw for securing back into position. Once this is done you can test the new cylinder and make sure it is securely within the door. You can now reconnect the handle to the door and then test it again. If everything is fine, your cylinder lock in your Upvc door has been replaced and you should have added another layer of security to your home.
Change upvc window locks repair
There are a variety of reasons a door handle or door knob may become loose. It could be due to the wear and tear on the handle or the square spindle within the handle. In this scenario, the door handle needs to be replaced.
Firstly it is important to ensure that the door is propped open and won't close in between the removal and replacement of the handle. Remove the screws from the inside surface of the handle plate by using the help of a screwdriver. This will release the handle from the plate. Don't lose the screws, as you may need to re-screw them later.
You can now take off the handles to access the cylinder lock inside the door. The cylinder lock is round or bulb-shaped, and is only used for multi-point locks on upvc as well as some aluminum doors. The procedure of changing the cylinder is similar to that of changing the handle, except you'll need to remove the old cylinder from the door and replace with a new one.
When choosing the replacement handle, it is important to consider its size. Make sure the handle is similar in size to the original as it will have to be able to slide over the existing screws that hold the handle in place. The best place to begin is by using a size matrix which will list the common sizes of replacement handles along with their keyhole center to handle plate distance.
It is also worth considering changing your handles for your Upvc doors to higher security standards like a Sold Secure SS301 or 2* Kitemark set of security handles. This will increase the security of your home and making it easier to operate the door. These sets are slightly more expensive, but the increased security and peace of mind is worth it. Having to constantly push the handle of the door upwards and downwards to open and shut it is not something you would like to be doing.
Change the Lock
The lock on your uPVC door can be a vulnerable point for burglars. Upgrade your uPVC to a multipoint locking system to ensure its security. This would include an open hook as well as a deadbolt to keep out burglars. A professional locksmith can assist you with this, but it is also possible to complete the work yourself. You'll need a few tools, but the process is quick and easy.
The first step is to loosen the screws that are holding the handle. Using a screwdriver, you can remove the screws and put them in a safe spot. Then, you lift the handle up to reveal the screw that holds the cylinder in its place. You can remove this screw and replace it with the new one. You should make sure that the screw is the same size as the original. It will need to be aligned correctly with the barrel of the lock.
Making changes to the lock on your uPVC door can seem intimidating. It is essential to the security of your home. If you make an error, it could leave you unable to unlock the door. If you are able to figure it out, it's quite simple and is less expensive than contacting a professional locksmith.
You'll need to remove the faceplate on the inside of the lock to replace the lock. You'll need to be able to see the screw that is located inside the door, as well as the bolt that holds it on the outside of the door. Once you have these screws in your hands, you can remove and replace the faceplate.
There are a variety of reasons you may need to replace the lock on your uPVC doors. It could be due to a lost key, a tenant has moved out but did not return keys, or you need to improve the security of your home.
Anyone with a basic DIY skill can replace the locking mechanism made of uPVC. If the lock is stuck, you will have to examine the hinges inside the mechanism. If the hinges are lubricated it is a simple repair. If you aren't confident doing this, it is best to consult an expert.